Equipment

The AT-VM95E/H combo kit includes the AT-VM95E dual moving magnet cartridge premounted on the AT-HS6BK headshell.Specifications: Cartridge & StylusFrequency Response 20 - 22,000 HzChannel Separation 20 dB (1 kHz)Vertical Tracking Angle 23°Vertical Tracking Force 1.8 to 2.2g (2.0g standard)Stylus Construction Bonded Round Shank

This VM95 Series cartridge with 0.3 x 0.7 mil elliptical stylus fits half-inch mount turntables. The cartridge’s special coil design delivers a powerful output level of 4.0 mV. It also offers excellent channel separation and low distortion for outstanding tonal quality. The durable, low-resonance housing includes threaded inserts that enable the cartridge to be mounted to the headshell with just two screws – no nuts required. And since all VM95 Series share the same body, the stylus can be replaced with any of the six interchangeable AT-VMN95 replacement styli.

The AT-HS6 is a universal ½"-mount headshell for 4-pin turntable cartridges. It features an ultra-lightweight (9 g) aluminum die-cast body to keep vibration to a minimum and a finger lift to enable precise stylus placement. The headshell is also equipped with gold-plated lead wires for lossless signal transmission and comes with mounting screws. Available in black (AT-HS6BK) and silver (AT-HS6SV). Specifications Material: Aluminum Connector: Aluminum Weight: 9.0 g (0.3 oz), including lead wire Dimensions: 13.0 mm (0.5") H × 21.4 mm (0.8") W × 48.9 mm (1.9") D Accessories: Installation screws (16 mm × 2, 10 mm × 2), nuts x 2, plastic washers x 2

2.7 x 0.26 mil Shibata replacement stylus for the AT-VM95 series cartridge.The Shibata stylus was originally developed to play four-channel (quadraphonic) vinyl records. The Shibata stylus has two radii, similar to an elliptical stylus. However, the radii of a Shibata stylus allow for more surface contact and effective pickup of ultra-high frequencies with less groove stress and distortion.SPECIFICATIONSFrequency Response: 20 - 25,000 HzChannel Separation: 23 dB (1 kHz)Vertical Tracking Angle: 23°Vertical Tracking Force: 1.8 to 2.2g (2.0g standard)Stylus Construction: Nude Square Shank

0.3 x 0.7 mil elliptical replacement stylus for the AT-VM95 series cartridge. Dual Moving Magnet Cartridge. Nude styli, shaped from whole diamonds, are more costly than bonded styli, with their diamond tips “bonded” to metal shanks before finishing. But because of their lower mass, nude styli track more accurately. Also, since our nude styli are grain-oriented, with their longest-wearing faces touching the record surface, they last longer.SPECIFICATIONSFrequency Response: 20 - 23,000 HzChannel Separation: 22 dB (1 kHz)Vertical Tracking Angle: 23°Vertical Tracking Force: 1.8 to 2.2g (2.0g standard)Stylus Construction: Nude Round Shank

2.2 x 0.12 mil Microlinear replacement stylus for the AT-VM95 series cartridgeThe Microlinear stylus almost exactly duplicates the shape of the cutting stylus that produces the original master disc (the disc used to create the pressed vinyl record). This likeness enables the Microlinear stylus to track portions of the groove other styli cannot reach, resulting in extremely accurate tracing of high-frequency passages and a flat frequency response within the audible range. The unique multilevel shape also wears more evenly, greatly extending record and stylus life.SPECIFICATIONSrequency Response: 20 - 25,000 HzChannel Separation: 23 dB (1 kHz)Vertical Tracking Angle: 23°Vertical Tracking Force: 1.8 to 2.2g (2.0g standard)Stylus Construction: Nude Square Shank

Replacement stylus for Audio-Technica AT3600L cartridge.Stylus Shape: Conical Stylus Dimension: 0.6 milSuitable for models such at the Audio Technica Sound Burger, LP60X and Coturn CT-1 turntables

Following in the footsteps of the legendary Nightclub series, the re-engineered Nightclub MkII boasts numerous sonic improvements in both club and studio settings. With a new cartridge body, the Nightclub MkII offers increased output voltage for powerful, energetic sound and enhanced performance from integrated phono preamps such as the ones found in DJ mixers. Superb sound quality! Club DJ and studio workers believe the Nightclub MkII to be an absolute high-end cartridge. It is indeed a no-nonsence performer with fascinating musical resources. Its output is superb with a frequency response rating high enough to compare Nightclub MkII to any audiophile cartridge. The special elliptical stylus guarantees sound with insignificant scratching. SPECIFICATIONSOutput voltage at 1000Hz, 5cm/sec. - 8 mVChannel balance at 1kHz - 1.5 dBChannel separation at 1kHz - 23 dBChannel separation at 15 kHz - 15 dBFrequency response - 20-20.000 Hz +/- 1.5 dBTracking ability at 315 Hz at recommended tracking force - 80 μmCompliance, dynamic lateral - 20 μm/m NStylus type: Special EllipticalStylus tip radius : r/R 13/25 μmTracking force range: 2.0-5.0g (20-50 mN)Tracking force recommended: 3g (30 mN)Tracking angle: 20°Internal impedance, DC resistance: 1.000 OhmInternal inductance: 580 mHRecommended load resistance: 47 kOhmRecommended load capacitance: 200-600 pF

Replacement stylus offers a tactile feedback when seating, indicating a snug and secure fit, while a cut-out area in the front allows for far more accurate needle drops. • Larger, wider and more robust stylus body• Easier to grip and handle• Better fix by metal spring• Tactile feedback of correct mount• Large stylus viewing cut‐outSPECIFICATIONSOutput voltage at 1000Hz, 5cm/sec. - 6 mVChannel balance at 1kHz - 1 dBChannel separation at 1kHz - 22 dBChannel separation at 15 kHz - 15 dBTracking ability at 315 Hz at recommended tracking force - 100 μmCompliance, dynamic lateral - 14 μm/m NStylus type: Spherical R 18 μmTracking force range: 3-5gTracking force recommended: 4gConcorde cartridge weight: 18.5g

The Concorde Scratch allows turntablist and scratching DJs to achieve new levels of performance with an unprecedented tracking ability and extra high output.• The SCRATCH is intended especially for scratching and back-cueing. The SCRATCH uses spherical styli, as they preserve more of the groove over backcueing and scratching. • For DJs that require increased tracking ability, the SCRATCH is up to the task. The Scratch has a supreme ability to trace the grooves of the records and it is tailored specifically for scratch. • Due to its very high output 10 mV, it is perfect for scratch of all music with deep bass frequences. With solid bass reproduction and extended highs, the SCRATCH is great for any style, providing energetic sound. Maximum scratch performance guaranteed!SPECIFICATIONSOutput voltage at 1000Hz, 5cm/sec. - 10 mVChannel balance at 1kHz - 1 dBChannel separation at 1kHz - 22 dBChannel separation at 15 kHz - 15 dBTracking ability at 315 Hz at recommended tracking force: 120 μmCompliance, dynamic lateral: 14 μm/m NStylus type: Spherical R 18 μmTracking force range: 3-5gTracking force recommended: 4gInternal impedance, DC resistance: 1200 OhmInternal inductance: 850 mHRecommended load resistance: 47 kOhmRecommended load capacitance: 200-400 pF

Black basic headshell (Technics style) with lead wires suitable for 4-pin scren in tone arms such as Technics 1200 or Audio Technica LP120x turntables.

• Color-coded lead wires made of high-purity 6N-0FC wire for connecting a phono cartridge to a headshell• Titanium-compunded wire sheath to improve damping effect• Gold-plated crimped lead tips• 6N-OFCC 99.9999% high-purity oxygen-free copper; 0.12 mm x 29 core strand construction

0.3 x 0.7 mil elliptical replacement stylus for the AT-VM95 series cartridge.SPECIFICATIONSFrequency Response: 20 - 22,000 HzChannel Separation: 20 dB (1 kHz)Vertical Tracking Angle: 23°Vertical Tracking Force: 1.8 to 2.2g (2.0g standard)Stylus Construction: Bonded Round Shank

The AT-LP60XBT gives you all the great features of the redesigned AT-LP60X fully automatic belt-drive stereo turntable with the added convenience of Bluetooth® wireless connectivity. The turntable pairs with speakers, headphones or other wireless devices. With its CSR BT chipset, the turntable is even able to connect to devices that support the aptX codec, which offers much-improved sound quality over the standard SBC code.Of course, the AT-LP60XBT can also be operated just like a regular turntable with a traditional wired connection. Either way – wired or wireless – you get outstanding audio with the ease of automatic operation controlled by front-panel start, stop and tonearm lift buttons.Audio-Technica has been a leader in phono cartridge design for more than 50 years, and that expertise shows in the AT-LP60XBT’s Dual Magnet™ cartridge with replaceable stylus. The cartridge is integrated into the headshell for assured performance and ease of setup. The AT-LP60XBT plays both 33-1/3 and 45 RPM records and comes with a 45 RPM adapter, a detachable dual RCA output cable (for wired connection) and a removable hinged dust cover. The turntable is available in black (AT-LP60XBT-BK), white/black (AT-LP60XBT-WH), and red/black (AT-LP60XBT-RD). SPECIFICATIONS Turntable Type: Fully automaticMotor DC servo-controlled Drive Method: Belt-driveSpeeds: 33-1/3 RPM, 45 RPMTurntable Platter: AluminiumWow and Flutter: Less than 0.25% (WTD) @ 3 kHz (JIS)Signal-to-Noise Ratio: >50 dB (DIN-B)Output Level: Pre-amp “PHONO”: 2.5 mV nominal at 1 kHz, 5 cm/sec Pre-amp “LINE”: 150 mV nominal at 1 kHz, 5 cm/secPhono Pre-Amp Gain: 36 dB nominal, RIAA equalizedPower Supply Requirements: 115/230V AC, 60/50 HzDimensions: 359.5 mm x 97.5 mm x 373.3 mmWeight: 2.6 kgAccessories: Included 3.5 mm (1/8") mini-plug (male) to dual RCA (male) output cable 45 RPM adapter Removable hinged dust cover

Whether you’re just getting into records, rediscovering a record collection long since buried away or simply adding a turntable to complete your system, the AT-LP60X fully automatic belt-drive turntable is an excellent choice. This affordable, easy-to-use turntable plays both 33-1/3 and 45 RPM records and, with its built-in switchable phono preamp, can be connected directly to your home stereo, powered speakers, computer and other components, whether they have a dedicated phono input or not.An update of the popular AT-LP60, the ATLP60X features a redesigned tonearm base and headshell to improve tracking and reduce resonance. Noise is further reduced by the inclusion of an AC adapter that moves the AC/DC conversion outside of the chassis where its impact on the signal chain is limited. Audio-Technica has been a leader in phono cartridge design for more than 50 years, and that expertise shows in the AT-LP60X’s Dual Magnet™ cartridge with replaceable stylus. The cartridge is integrated into the headshell for assured performance and ease of setup. The turntable comes with a detachable RCA output cable (3.5 mm male to dual RCA male), 45 RPM adapter, and a removable hinged dust cover.SPECIFICATIONS Turntable Type: Fully automaticMotor DC servo-controlled Drive Method: Belt-driveSpeeds: 33-1/3 RPM, 45 RPMTurntable Platter: AluminiumWow and Flutter: Less than 0.25% (WTD) @ 3 kHz (JIS)Signal-to-Noise Ratio: >50 dB (DIN-B)Output Level: Pre-amp “PHONO”: 2.5 mV nominal at 1 kHz, 5 cm/sec Pre-amp “LINE”: 150 mV nominal at 1 kHz, 5 cm/secPhono Pre-Amp Gain: 36 dB nominal, RIAA equalizedPower Supply Requirements: 115/230V AC, 60/50 HzDimensions: 359.5 mm x 97.5 mm x 373.3 mmWeight: 2.6 kgAccessories: Included 3.5 mm (1/8") mini-plug (male) to dual RCA (male) output cable 45 RPM adapter Removable hinged dust cover

This fully manual turntable is modeled after the AT-LP120XUSB, but adds the convenience of Bluetooth® wireless connectivity to the existing analog and USB outputs.Featuring a specially designed DC servo direct-drive motor and adjustable dynamic anti-skate control, the AT-LP120XBT-USB plays 33-1/3, 45, and 78 RPM records and outputs the high-fidelity audio to the device of your choice. Use the included RCA output cable along with the built-in selectable phono preamp to connect to your home stereo or powered speakers. Use the USB cable to connect to your computer and then download the free Mac- and PC-compatible Audacity recording software, or software of your choice, to start converting your records to digital audio files. Or use the Bluetooth wireless technology to pair the turntable with wireless speakers, headphones or other devices, including those that support the high-quality Qualcomm® aptX™ audio codec.The turntable also features an S-shaped tonearm with adjustable tracking force and an AT-HS6 universal ½"- mount headshell with an AT-VM95E Dual Moving Magnet™ phono cartridge. Audio-Technica has been a leader in phono cartridge design for more than 50 years, and that expertise shows in the versatile, high-performance AT-VM95E. The cartridge comes with a 0.3 x 0.7 mil elliptical stylus, but is also compatible with any VM95 Series replacement stylus, offering a wide choice of options for every budget and application.Additional professional features include a die-cast aluminium platter with felt mat; a start/stop button; selectable high-accuracy quartz-controlled pitch lock and pitch change slider control with +/-10% adjustment range; a stroboscopic platter with speed indicator; a removable plug-type stylus target light; external power supply; and a removable hinged dust cover.BLUETOOTHCompatible with most Bluetooth® speakers and headphones, the LP120XBT-USB pairs seamlessly to your devices. Simply press the Bluetooth® button, located next to the tonearm, for 4 seconds and connect to your chosen speakers, it’s that simple.You can also connect to Bluetooth® wireless headphones, giving you the flexibility to enjoy your vinyl records without the clutter of wires or having to be near your turntable and music setup. Sink into your comfiest chair and wirelessly enjoy over half a century of Japanese audio engineering and sound excellence.PLUG & PLAYThe LP120XBT-USB is designed to give you a high-quality listening experience that’s easy to enjoy right out of the box. A built-in preamp means the LP120XBT-USB can be plugged directly into your existing speakers, or, with the simple press of a switch, connect wirelessly via Bluetooth® 5.0 to any bluetooth compatible speaker, supported home assistant or wireless headphones. Space saving with no external amps, no clutter and no mess; just incredible sound and reliable features designed with over half a century of Japanese audio innovation.The LP120XBT-USB can also be plugged directly into your computer, for audio playback via your PC speakers or for simple and easy backup and transfer of your vinyl records to playback on your smart devices when on-the-go.SPECIFICATIONSTurntable Type: 3-speed, fully manual operationMotor: DC servo motorDrive Method: Direct driveSpeeds: 33-1/3 RPM, 45 RPM, 78 RPMTurntable Platter: Die-cast aluminumStarting Torque: >1.0 kgf.cmBraking System: Electronic brakeWow and Flutter: <0.2% (WTD) @ 3 kHz (JIS)Signal-to-Noise Ratio: >50 dBOutput Level Pre-amp: “PHONO”: 4 mV nominal at 1 kHz, 5 cm/secPre-amp “LINE”: 240 mV nominal at 1 kHz, 5 cm/secPhono Pre-Amp Gain: 36 dB nominal, RIAA equalizedUSB Function: A/D, D/A – 16-bit/44.1 kHz or 48 kHz USB selectable; Computer interface – USB 2.0 Compliant Windows 7 or above, or MAC OS X or abovePower Supply Requirements: 100 to 240 V, 50/60 Hz, 1.5A MaxPower Consumption: 2.75 WDimensions: 452.0 mm (17.80") W x 352.0 mm (13.86") D x 141.6 mm (5.57") HWeight: 8 kg (17.6 lbs.), without dust coverAccessories Included: AT-VM95E phono cartridge; AT-HS6 headshell; 1.9 m (6.2') USB cable; dual RCA (male) to dual RCA (male) cable with ground wire; counterweight; felt mat; dust cover; 45 RPM adapter; plug-type stylus target lightTonearm Type: Balanced S-shaped tonearm with detachable headshellEffective Arm Length: 230.5 mmOverhang: 16 mmTracking Error Angle: Less than 3 degreesApplicable Cartridge Weight: 3.5-8.5 gAnti-skating Range: 0-4 gReplacement Stylus: AT-VMN95ECommunication System: Bluetooth Version 5.0Maximum Communication Range Line of sight - approx. 10 m (33')Compatible Bluetooth Profile A2DPSupport Codec SBC, Qualcomm® aptX™ audio